BICYCLE COMPUTER WHEEL SIZE SETTINGS


bike computer wheel size setting

Do you use a bicycle computer? If so, is it accurate (or akwert as one of my teachers used to pronounce the word)? Getting a computer set accurately can be a bit challenging unless you know what you are doing. Some people settle for their computers to be inaccurate often times not realizing how far off they are and how many extra miles they are showing than they really rode or miles they are failing to show that were ridden.

There are different ways to go about setting a bike computer so it will be accurate. I will confess that I personally have only used one of them. I am happy to report that my computer is about as close as is humanly possible in getting it set accurately.

So let’s get into this. Each bicycle computer should come with instructions which have a ‘chart’ showing the numbers used for various wheel sizes. That often will only get you in the ball park however, and “fine tuning” is required from there. Our local trail system has accurate mile markers (actually every 1/4 of a mile) so I use those to set my bike computer. The tires used will effect things as well. A lower profile (outside diameter) tire will be different than a higher profile tire. Tire inflation will also make a difference so it is best to have the tires inflated to whatever pressure you normally use when making any computer setting adjustment. Even rider weight effects the setting. Depending upon how far off the current setting is the amount of change in the number setting may only be “1” or if it is off quite a bit it may be considerably more. If your mileage shown is under you need to increase the number used in the setting. If your mileage shown is over you need to decrease the number used in the setting.

It is best to check your accuracy over a longer distance … like 5 miles rather than only 1 mile. And once you find that magical number write it down for safe keeping. And if you switch to other tires and the number is different write that tire and number down. It sure makes it a lot easier when you switch between tires.

          **********

Here are some instructions on how to set your computer using the measured mile method:

1.0 (the measured mile)
Cyclometer Reading x Old Setting = New Setting
For example: If you set your 26×2.1 wheel size to: 2091 and rode the measured mile and came up short, maybe your computer read .95 miles, then you’d do:

1.0 (the measured mile)
0.95 (what your computer read) x 2091 (old setting) = 2201 (new setting)
If you computer read too long, maybe 1.05, you’d still do the same formula and your setting would be:

1.0 (the measured mile)
1.05 (what your computer read) x 2091 (old setting) = 1991 (new setting)
To help you out, enter your numbers here:

Your Initial Wheel Size Setting:
2091
Actual Distance Ridden:
1.0
Reading on Bike Computer:
1.05
Okay, change your bike computer setting to this:
1991

**********

HERE is a very handy calculator to determine the number you need to enter if you have the computer reading for a measured mile. The calculator is located at the very bottom of this webpage.

As I stated early on there are various methods of determining the number needed to set up a bike computer wheel size so it records accurately.

HERE is Sheldon Brown’s charts on this subject of computer setting for wheel size. And here is a video showing how this is done.

 And HERE is another online chart.

HERE is an online calculator for determining the wheel size setting.

Here is a video showing how to use a tape measure to determine the outside circumference of a bike tire and use that number to set the computer wheel size. This is sometimes referred to as the Roll Out method.

Lastly HERE is the Google search results for this subject. There is lots of helpful information online about this.

And hopefully the following will make things very easy, quick and handy for those of you who use any of these 20 inch tires. These are the magical numbers I have recorded for myself when I have ran various Schwalbe tires.

Kojak 1496
Marathon (1.5 width) 1425
Marathon Plus (1.75 width) 1561
Tryker 1537

I have ran a couple of others, but don’t have the number recorded for them. I can’t guarantee that these numbers will work for you but I think they would be close. Like I said, there are various factors which determine what number is needed for each of us … our weight, tire pressure and weight hauling/loading on the trike … may mean your number will be different from mine. It is really not Mission Impossible so hopefully you can get your computer set accurately and from then on just …

KEEP ON TRIKIN’

Before leaving this subject of bike computers I want to touch on the magnets that attach to the spokes. My bike computer came with the type on the left in the image below …

bike computer spoke magnets

which works, of course, but a friend of mine was throwing out one of his as he replaces his bike computer from time to time (the more expensive ones like he buys don’t seem to last). Anyway, I took it to use in place of my magnet and have found it to be better as it doesn’t get bumper around nearly as easily and seems to be less sensitive as far as it’s position. I rarely have had any issues with it, but I did with the original one that came with my computer.

Advertisements

About Steve Newbauer

I have a few current blogs (tadpolerider1, navysight, and truthtoponder) so I am keeping busy. I hope you the reader will find these blogs interesting and enjoy your time here. Feel free to email me at stevenewbauer at outlook.com

Posted on May 6, 2016, in accessories, tadpole trikes, tips and tagged , . Bookmark the permalink. Comments Off on BICYCLE COMPUTER WHEEL SIZE SETTINGS.

Comments are closed.